Battery charge controller G4 440 AMP 24V solar panel wind turbine G4 / NO BASE

Description

You are bidding on a 24 Volt battery controller to prevent over-charging
by simple dumping or cutting of incoming power.
Works well with any 24 volt battery banks built up of 6 or 12 volt series / parallel
battery bank cells that equal 24 volts / cell arrangements.
NO-BASE  / Economy Model
CLICK HERE TO SEE 24V / 1000 Watt DUMP LOAD
Our most versatile model is this 24 volt system that can be micro programmed by the operator to keep a 12 volt lead acid, gel, Li-ion, EB and just about any battery that works in the voltage ranges from 11 to 14.4 volts. You set the exact voltages and fine tune to your needs with the simple programming buttons.
(See video's - cut and paste the URL's into any web browser bar)
https://youtu.be/81y50tpSads
https://youtu.be/rVffRzl6zcY
https://www.youtube.com/watch?v=f9_P2rfQzgs
https://www.youtube.com/watch?v=f9_P2rfQzgs
https://www.youtube.com/watch?v=IZRahrogJ_A
https://www.youtube.com/watch?v=NZENiUNoHWo
SEE a Great Video on how to use it below
HOW TO PROGRAM IT
CLICK HERE
WIND/SOLAR 24 VOLT 220 AMP  DUMP / DISCONNECT CHARGE CONTROLLER
WITH BUILT IN DIGITAL DISPLAY AND INTELLIGENT DUAL PROCESSOR CONTROLLER
(With Original "THEM" Thermodyne Controller
. Says THER on the board. Made with real high voltage rated parts.
Some people claim Thermodyne made but only boards stamped "THER" are genuine Thermodyne boards)
For solar panels and solar
IT CAN DISCONNECT THE INCOMING POWER
OR DIVERT IT
TO A DUMP LOAD.
Max solar amperage in divert (dump) mode is  440 amps. This is a big hybrid wind and solar charge controller.
Use for wind or solar or both at the same time! Also use for hydroelectric or solar or both.
User changeable settings -- Several controllers on the market only let you set the dump level!
Connect multiple turbines and solar panels up to 440 amps worth at the same time!
Max continuous solar amperage in disconnect mode is 100 amps. REBUILT WITH NEW WIRING.
Can divert the charging source from the batteries to the load, or dump both the batteries along with the charging source.
You can connect both wind and solar at the same time. Reverse polarity protection
Ultra low power consumption even with the volt meter on (almost negligible). You can even set the volt meter to turn off after in-activity.
On board relay- Isolates electronics from back voltage spikes from large 440 amp relay.
This is important to get the longest life out of the electronics. No body else has this!
Dual (2) Microprocessor controlled -- Extremely  stable and very accurate
Multiple user changeable settings, and trip points for many various system requirements and applications- You can change the dump point voltage level,
end of dump voltage level, length of time in divert mode when end dump point voltage is reached
Isolated Electronics Protection - Impossible to accidentally connect wind or solar directly to the circuit board.
High amp rating - 440 amps, 10,000 watts surge peak max.
Battery Status digital LED - Lets you know your battery's actual voltage in real time!
Green LED come on and then you know it's in dump mode or cut mode depending on how your relay lugs wired.
Plug and Play - Long leads for easy termination to your 24 volt battery or battery bank.
Battery regulator for both your wind and solar battery input power. This
regulator can either dump extra power creating free hot water or heat or
just cut off extra power to keep your batteries from over charging. This
unit is a must for wind turbine applications as it uses a mechanical
relay which can handle high voltage surges unlike solid state controllers.
This item is the only controller that will work with wind turbines Do not buy solid state controllers as they will burn out in high wind conditions.  This controller was specially developed for wind turbines. Also works on solar too - Get one battery controller to do it all!
Worlds Lowest Cost 440 AMP
Wind & Solar Controller
Battery Regulator-
Cut/Disconnect Controller-
Diversion Load Regulation-
If you use it as a DIVERSION or DUMP load MODE then it uses almost no power when it is NOT dumping (energy efficient sensing)
In DISCONNECT mode it draws .2 amps but that's good since that means you have too much power in your batteries anyhow.
This High Amp unit can control 12
wind turbine batteries or 40 solar panels !
Used to prevent battery over
charging on
Wind - Solar - Hydro
A battery regulator diverts excess power to power
some other useful device when ever your battery is full.
Use the this excess power to make free hot water or
to
recharge an auxiliary battery bank, so many uses!
An extremely robust unit!
draws almost ZERO power while sensing! 99.998% electrically efficient while sensing!
This controller may look fiendishly simple but it took 16 years of labor, custom parts and and testing in order to prove the basic concept was
dependable.
Built to take over 500 Million cycles or about 85 years of switching for the average system. TESTED for 16 years and proven 100% durable!
Battery regulator.
Charge regulator.
Charge controller.
Dump load regulator.
"Cut" charge controller.
Diversion load regulator.
Micro processor controlled.
Versatile raised steel mounting plate.
Measures 10" long by 7" wide by 3" tall.
Works for all Wind Turbines, Solar panels and Hydro.
For all voltages ranges in multiple battery banks.
No grounded IGBT's or MOSFETS - Lighting strike proof isolation.
CUT -LOAD
controller (No need to buy a dump load resistor)
Electrically efficient. Draws only trace power while
sensing
!
Does not waste electricity while
sensing
in  diversion load mode!
HOW POWER DRAW DYNAMICS WORKS:
If you use it as a DIVERSION or DUMP load MODE then it uses no power when it is NOT dumping (energy
efficient
sensing)
The modern way to monitor your battery from over charging is to have a diversion load that performs another task such as heating water when your battery is in danger of over charging. Shutting down the output of your wind turbine or your other renewable energy devices is old school thinking. Now-a-days most people dump their excess power into some other legitimate device optimizing their energy independence. Hot water from your excess power can be used for radiant heating in the winter or even in the hot summer months for washing cloths or dishes and for bathing. You will always find a need for hot water in your life.
"Simple and ultra-reliable" - "A BULLET PROOF SYSTEM"
[isdntekvideo]